Εγχειρίδιο Crivit IAN 282673 Υπολογιστής ποδηλασίας

Εγχειρίδιο

GB/CY

GB/CY GB/CY GB/CY GB/CY GB/CY

GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY

GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY

GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY GB/CY

Resetting the bicycle

computer

Press and hold the SET button

20

first and hold

the MODE button

14

to proceed to setting

mode. SETTING OPEN or SETTING RESET will

be displayed. Press the MODE

14

button until

SETTING RESET displayed, Confirm reset the

product by press the SET button

20

.

Now you can adjust the previously configured

basic settings (language, age, weight, time).

Other saved information will be deleted.

Replacing the battery

Note: The bicycle computer battery must be

replaced when the battery state indicator

18

is

shown on the LC display . Press and hold the MODE

button

14

first and hold the SET button

20

at the

same time and keep them pressed until the battery

symbol and {{----}} are shown on the LC display. To

replace the battery, proceed as shown in figure A.

pressing the MODE button

14

you can switch

between the ADVANCE and EASY modes.

EASY mode, press and hold the SET button

20

to request setting mode. Press the SET button

20

again. Press the MODE button

14

to activate

or deactivate individual settings (i.e.CLOCK).

Select “ON“ to add the selected function to

EASY mode. Select “OFF“ if you do not wish

to add the selected function to EASY mode.

Press the SET button

20

to confirm your entry.

Press the MODE button

14

to proceed to the

next function and repeat the steps as described

above.

Press the MODE button

14

to exit settings.

Using the backlight

Press the SET button

20

to temporarily activate

the backlight. The backlight will switch off auto-

matically after a short amount of time.

SCAN: Scan

Note: In scan mode, the display switches automati-

cally between the trip distance, maximum speed,

average speed and trip time.

Note: Refer to the “Basic settings“ chapter to

configure the settings.

Note: To deactivate scan mode press the MODE

button

14

to return to ADVANCE mode.

CUSTOMIZE mode

Alongside ADVANCE and EASY mode, you can

also apply your own settings in CUSTOMIZE mode.

There are two ways of requesting CUSTOMIZE

mode:

a) Press and hold the SET button

20

first and hold

t

he MODE button

14

to proceed to setting m

ode.

SETTING OPEN or SETTING RESET will be dis-

played. Press the MODE

14

button until SETTI

NG

OPEN displayed. Press the SET button

19

enter

to select ADVANCE or EASY. By repeatedly

ETA: Expected time arrival.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to request

the ETA distance count down. Press the MODE

button

14

and press the SET button

20

again

request the ETA time and ETA countdown timer

for selected.

KM: Kilometer counter.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to request

the kilometer counter settings. The LC display will

show the symbol for increasing or decreasing

the number (+ or -) and distance counter value.

TIME: Timer.

Press and hold the SET button

20

for 3 seconds

to change the timer settings. The LC display will

show the symbol for increasing or decreasing

the number (+ or -) and timer counter value.

STPWATCH: Stopwatch.

Press the SET button

20

to start the stopwatch.

Press the SET button

20

again to stop the stop-

watch. Press and hold the SET button

20

for

3 seconds to set the stopwatch to 0.

CAL RATE: Current calorie consumption.

CALORIE: Calorie counter.

Press and hold the SET button

20

for 3 seconds

to set the calorie counter to 0.

FAT-BURN: Fat-burning in grams.

Press and hold the SET button

20

for 3 seconds

to set the fat-burning value to 0.

CO2 KG: CO2 saved.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to request

the reference value for CO2 setting.

FUELSAVE: Fuel save comparison with a car.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to request

th

e fuel unit and fuel consumption setting.

MAXSPEED: Maximum speed.

Press and hold the SET button

20

for 3 seconds

to set the maximum speed to 0.

AVGSPEED: Average speed.

Press and hold the SET button

20

for 3 seconds

to set the average speed to 0.

TRIPTIME: Trip time.

TEMP: Thermometer.

Press the SET button

20

to display the maximum

temperature value reached (HI). Press the SET

button

20

again to display the lowest tempera-

ture value reached (LO). Press the SET button

20

and keep it pressed while the highest or lowest

temperature is displayed to return to the current

temperature and delete the saved information.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to request

temperature unit setting.

> CO2 KG >FUELSAVE > ETA > KM+ / - >

TIME+ / - > SCAN

CLOCK: Displays the time.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to request

the time and date settings.

TOTALODO: Total mileage counter.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to change

the tyre size, ODO and maintenance interval

settings.

TOTAL-TM: Total trip time.

Press and hold the SET button

20

for 3 seconds

and press the SET button

20

again to change

the saved total trip time.

TRIPDIST: Trip distance.

Press and hold the SET button

20

for 3 seconds

to set the trip distance, average speed and trip

duration to 0.

Using the bicycle computer

Note: The bicycle computer will automatically

switch to standby mode when it has not been used

for over 5 minutes. Pressing any button or vibrations

will reactivate the computer. The function indicator

will show the current mode

Press the MODE button

14

repeatedly to scroll

through the different functions(see the chapter

o

n “Using the functions“). Press and hold the S

ET

button

20

to request or reset the saved values.

The bicycle computer features the

following functions:

ADVANCE mode: By pressing the MODE button

14

you can select the following function displays:

CLOCK > TOTALODO > TOTAL-TM > TRIPDIST >

MAXSPEED > AVGSPEED > TRIPTIME > TEMP >

STPWATCH > CAL RATE > CALORIE > FAT-BURN

Confirm your choice using the SET button

20

.

Press the MODE button

14

to exit settings. You

have now successfully configured the basic

settings.

If you wish to change the basic settings, please

follow the steps outlined in the chapter “Reset-

ting the bicycle computer“ and reset all basic

settings.

Connecting the bicycle

computer to the sensor

Use the magnet

1

to trigger the sensor

6

, the

velocity display

13

shows a curve to confirm

successful connection. The bicycle computer

8

is now ready to use. If the connection breaks,

please follow the steps in the chapter “Trouble-

shooting“ and reset all basic settings. You will

then have to reestablish the connection between

the bicycle computer

8

and the sensor

6

.

– Date format: DD-MM-YY or MM-DD-YY can

be select.

– Date: Year, month and day can be input.

– CO2 saved: 3 digit number can be input.

– Maintenance interval: 3 digit number can be input.

Note: If the maintenance interval input “000” will

switch off the service indicator.

– Light ON / OFF: Switch ON or OFF the back

light. If selected back light ON, you can input

the back light ON and OFF time.

– ETA distance: 5 digit number can be input.

– ETA mode: CLOCK or TIME for select.

– Fuel format: LITER or GALLON can be select.

– Fuel cons: 3 digit number can be input.

– Unit of temperature: °C or °F can be select.

Important functions:

MODE button

14

to configure values / SET button

20

to edit and adopt settings

– Language: 6 language can be select.

– Application profile: ADVANCE or EASY can

be select.

– Tyre size: Enter the circumference for your tyres

sizs in mm, 4 digit number can be input.

Note: You can calculate your tyre circumference

(U) by multiplying the tyre diameter (D) by 3.1416

(Fig. M). The list (Fig. N) features the tyre circumfer-

ences (U) of conventional tyre diameters (D).

– Unit of length: KM / KMH or MILE / MPH can

be select.

– Age: 2 digit number can be input.

– Unit of weight: KG or LB can be select.

– Weight: 3 digit number can be input.

– Time format: 12 or 24hrs can be select.

– Time: hour and min can be input.

Attaching the bicycle computer

To attach the product, proceed as depicted in

Fig. B to I.

Trim the protruding ends of the cable ties

2

using a suitable tool such as a side cutter.

Note: Ensure that the bicycle computer

8

is

attached less than 70 cm from the sensor

6

.

Attach the bicycle computer

8

to the sensor

6

within a 30 ° angle, see Fig. B.

Initial use

Changing basic settings

Basic settings: Language > Application profile >

Tyre size > Unit of length > Age > Unit of weight >

Weight > Time format > Time > Date format > Date

> CO2 saved >Maintenance interval >Light ON /

OFF > ETA distance > ETA mode > Fuel format >

Fuel cons > Unit of temperature

Before use

Remove the protective film from the LC display

13

before you use the device for the first time.

Note: Do not use this product on electric bikes.

The motor could cause the product to malfunction.

Inserting the battery

To insert the battery

3

proceed as depicted

in Fig. A.

Use a coin to open the battery compartment.

Use this to turn the battery cap counter-clock-

wise. Ensure that you insert the battery correctly

into the battery compartment (polarity). This is

shown in the battery compartment. Ensure that

the O-ring is attached correctly before inserting

the battery.

Turn the battery cap clockwise onto the battery

compartment using the coin to close it.

rechargeable battery

and the product.

Clean the contacts on

the battery / rechargea-

ble battery and in the

battery compartment

before inserting!

Remove exhausted

batteries / rechargeable

batteries from the product

immediately.

the product will not be

used for a longer period.

Risk of damage of

the product

Only use the specified

type of battery /

rechargeable battery!

Insert batteries / rechar-

geable batteries accord-

ing to polarity marks (+)

and (-) on the battery /

In the event of a leakage

of batteries / rechargeab

le

batteries, immediately

remove them from the prod-

uct to prevent damage.

Only use the same type

of batteries / rechargea-

ble batteries. Do not mix

used and new batteries /

rechargeable batteries.

Remove batteries /

rechargeable batteries if

and seek immediate

medical attention.

WEAR PROTEC-

TIVE GLOVES!

Leaked or damaged bat-

teries / rechargeable bat-

teries can cause burns

on contact with the skin.

Wear suitable protective

gloves at all times if such

an event occurs.

t

emperatures, which could

affect batteries / rech

arge-

able batteries, e.g. radi-

ators / direct sunlight.

Avoid contact with the

skin, eyes and mucous

membranes. In the event

of contact with battery

acid, thoroughly flush

the affected area with

plenty of clean water

Never throw batteries /

rechargeable batteries

into fire or water.

Do not exert mechanical

loads to batteries /

rechargeable batteries.

Risk of leakage of

batteries / rechargeable

batteries

Avoid extreme environ-

mental conditions and

DANGER OF

EXPLOSION!

Never recharge non-re-

chargeable batteries.

Do not short-circuit bat-

teries / rechargeable

batteries and / or open

them. Overheating, fire or

bursting can be the result.

Safety

instructions for

batteries /

rechargeable

batteries

DANGER TO LIFE!

Keep batteries / recharge-

able batteries out of reach

of children. If accidentally

swallowed seek immedi-

ate medical attention.

Please note that the guar-

antee does not cover

damages caused by incor-

rect handling, non-com-

pliance with the safety

instructions or use by

unauthorised persons.

lacking experience and

knowledge, when super-

vised or instructed in the

safe use of the product

and understand the asso-

ciated risks. Do not allow

children to play with the

product. Cleaning and

user maintenance must

not be performed by chil-

dren without supervision.

General safety

instructions

KEEP ALL SAFETY NOTICES

AND INSTRUCTIONS FOR

FUTURE REFERENCE!

This product may be used

by children 8 years and

up as well as persons

with physical, sensory or

mental impairments or

Scope of delivery

1 Wireless bike

computer

1 Bracket for bicycle

computer

1 Damper for bicycle

computer bracket

1 Bracket with sensor

1 Magnet

6 Cable ties

2 Batteries, 3 V

(direct current),

Model CR2032

button cell battery

2 Replacement O-rings

for bicycle computer

and sensor

1 Instructions for use

15

Speed comparator display:

Compares the current speed with the

average speed

▲ higher than the average speed

▼ lower than the average speed

16

SCAN display

17

Maintenance interval display

18

Battery state indicator

19

Speed tendency:

This displays the trend in terms of whether

the speed is increasing (large bar, right) or

decreasing (small bar, left).

20

SET button (S)

Technical data

Battery: 3 V (direct current)

(CR2032 button cell

battery)

Operating temperature: 0–50 °C

- ETA (Estimated time of arrival)-Distance

- ETA time

- Fuel Saving

- Back light ON / OFF

Parts Description

1

Magnet

2

Cable ties

3

Battery

4

Damper for bicycle computer bracket

5

Bracket

6

Sensor

7

Bicycle computer battery cap

8

Bicycle computer

9

Sensor battery cap

10

Primary functional value display

11

Function indicator

12

Secondary functional value display

13

LC display

14

MODE button (M)

Functions

– Menu languages: GB, DE, FR, NL, IT, ES

– Clock

– Stopwatch

– Temperature display °C / °F

– Memory function for min. and max. temperature

– Bike speed display (0–99.9 km / h)

– Average speed display (0–99.9 km / h)

– Maximum speed display (0–99.9 km / h)

– Speed comparator

– Speed trend

– Trip timer (max. 9:59:59) (Countdown or

forward-counting)

– Odometer (Countdown or forward-counting)

– Total kilometer and total trip time display

– Calorie counter

– Fat burning display

– CO2 saved

– Scan display (functions are interconnected)

– Automatic start function

Wireless bike computer

Introduction

We congratulate you on the purchase of your new

product. You have chosen a high quality product.

The instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the product as

described and for the specified applications. If you

pass the product on to anyone else, please ensure

that you also pass on all the documentation with it.

Intended use

The product is intended to be used as a bicycle

computer. Not for commercial use.

WIRELESS BIKE COMPUTER

БЕЗЖИЧЕН ВЕЛОКОМПЮТЪР

Инструкции за обслужване и безопасност

ΑΣΎΡΜΑΤΟΣ ΥΠΟΛΟΓΙΣΤΉΣ

ΠΟΔΗΛΆΤΟΥ

Υποδείξεις χειρισμού και ασφαλείας

WIRELESS BIKE COMPUTER

Operation and Safety Notes

IAN 282673

G

F

E

D

B

I

H

J

10

11

14

15

16

17

18

19

5

3

4

6

C

1

2

8

1

6

5 2

4

2

6

6

2

1

1 6

max.

2 mm

6

1

20

12

13

A

7

3

8

6

3

9

D

U

M

N

D U

20

1598 mm

22

1759 mm

24

1916 mm

26

(650 A) 2073 mm

26,5

(Tubular) 2117 mm

26,6

(700 x 25C) 2124 mm

26,8

(700 x 28C) 2136 mm

27

(700 x 32C) 2155 mm

28

(700B) 2237 mm

ATB24

x 1,75 1888 mm

ATB26 x1,4 1995 mm

ATB26 x1,5 2030 mm

ATB26 x1,75 2045 mm

ATB26 x 2 (650B) 2099 mm

27

x 1 2138 mm

27

x 1 1 / 4 2155 mm

L

K

8

5

1

Βαθμολογία

Περισσότερα για αυτό το εγχειρίδιο

Κατανοούμε ότι είναι ωραίο να έχετε ένα χάρτινο εγχειρίδιο για το Crivit IAN 282673 Υπολογιστής ποδηλασίας σας. Μπορείτε πάντα να κατεβάσετε το εγχειρίδιο από τον ιστότοπό μας και να το εκτυπώσετε μόνοι σας. Εάν θέλετε να έχετε ένα πρωτότυπο εγχειρίδιο, σας συνιστούμε να επικοινωνήσετε με το Crivit. Μπορεί να είναι σε θέση να παρέχουν ένα πρωτότυπο εγχειρίδιο. Αναζητάτε το εγχειρίδιο του Crivit IAN 282673 Υπολογιστής ποδηλασίας σας σε διαφορετική γλώσσα; Επιλέξτε τη γλώσσα που προτιμάτε στην αρχική μας σελίδα και αναζητήστε τον αριθμό μοντέλου για να δείτε αν τον έχουμε διαθέσιμο.

Προδιαγραφές

Όλα τα εγχειρίδια για Crivit Υπολογιστές Ποδηλασίας
Περισσότερα εγχειρίδια του Υπολογιστές Ποδηλασίας

Συχνές ερωτήσεις σχετικά με Crivit IAN 282673 Υπολογιστής ποδηλασίας

Η ομάδα υποστήριξής μας αναζητά χρήσιμες πληροφορίες προϊόντος και απαντήσεις σε συχνές ερωτήσεις. Εάν εντοπίσετε ανακρίβεια στις συνήθεις ερωτήσεις μας, ενημερώστε μας χρησιμοποιώντας τη φόρμα επικοινωνίας.

Σχετικά προϊόντα

Εγχειρίδιο

Crivit IAN 270550 Υπολογιστής ποδηλασίας

Εγχειρίδιο

Crivit IAN 97799 Υπολογιστής ποδηλασίας

Εγχειρίδιο

Crivit IAN 109642 Υπολογιστής ποδηλασίας

Εγχειρίδιο

Crivit IAN 275091 Υπολογιστής ποδηλασίας

Εγχειρίδιο

Crivit IAN 103553 Υπολογιστής ποδηλασίας

Εγχειρίδιο

Crivit IAN 79107 Υπολογιστής ποδηλασίας

Εγχειρίδιο

Crivit IAN 87309 Υπολογιστής ποδηλασίας

Εγχειρίδιο

Crivit IAN 286004 Υπολογιστής ποδηλασίας

Σχετικές κατηγορίες