Εγχειρίδιο Bionaire BFH3520 Θερμάστρα

Εγχειρίδιο

Setting the Off Timer:

1. Select the Mode and/or temperature you wish

the heater to run in.

2. While the heater is running, press and hold

the up (+) and down (-) buttons simultaneously.

3. By pressing the up (+) and down (-) buttons,

program the heater to turn off in up to 16 hours

from the current time, in increments of 1 hour.

4. After setting the timer, the LCD display will

return to show the current room temperature.

An LED will illuminate to show that the timer is

activated.

5. After the predetermined length of time has

passed, the heater will automatically shut off.

Setting the On Timer:

1. While the heater is off, press and hold the up

(+) and down (-) buttons simultaneously.

2. By pressing the up (+) and down (-) buttons,

program the heater to turn on up to 16 hours in

advance of current time, in increments of 1 hour.

3. After the preset length of time has passed, the

heater will automatically turn on Auto Mode HI

Power at 24°C for a preset time of 2 hours.

OSCILLATION INSTRUCTIONS

Press ( ) button J to start and ( ) button J

again to stop oscillation.

REMOTE CONTROL INSTRUCTIONS

Before operation, insert 2 “AAA” batteries (not

included) into the back of the remote control. Remove

batteries before discarding the remote control.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (nickel-cadmium) batteries.

The remote control for this unit has the capability

of operating all control panel functions (see Fig.

3, 4).

POWER: To turn the unit on press the

Mode ( ) button. To turn the unit off press the

Mode ( ) button.

MODES: To scroll through the various modes

FA, HI, LO, AH, AL and AF press the Mode ( )

Button until you reach your desired setting.

OSCILLATION: To start oscillation, press the

Oscillation ( ) Button once. To stop oscillation

press the button again.

TEMPERATURE: The temperature can be

adjusted only when the unit is set on the Auto

Mode Hi (AH) and Auto Mode Lo (AL).To

increase the temperature setting, press the (+)

button. To decrease the temperature setting that

you desire press the (-) button.

TIMER: To activate the timer from the remote

control, press the Timer Button ( ). From there

you can press the (+) or (-) button, which will

give you the ability to program the heater to turn

on or off in 1 hour increments, up to 16 hours.

For more information see Using Programmable

Timer instructions above.

AUTO SAFETY SHUT-OFF

This heater is equipped with a technologically

advanced, safety system that requires the user

to reset the heater if there is a potential overheat

situation. When a potential overheat temperature

is reached, the system will automatically shut

the heater off. It can only resume operation

when the user resets the unit.

To reset the heater

1. Press the MODE ( ) button.

2. Unplug the heater and wait for 30 minutes for

the unit to cool down.

3. After the 30 minutes, plug the unit in again

and operate normally.

Tip Over Protection

When the unit is accidentally knocked over, it will

instantly shut off. To reset, simply place the

heater in an upright position.

Safety Back-Up Fuse

In the unlikely case the heater does not respond

to an overheat situation, the safety back-up fuse

will engage. In this case, the heater will not

reset. Please contact your local service number

for advice.

PLEASE READ AND SAVE THESE

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including

the following:

1. Before connecting the heater, check that the

voltage indicated on the rating plate

corresponds to the main voltage in your

home/office.

2. WARNING: In order to avoid overheating,

do not cover the heater ( ).

3. DO NOT position the heater directly under a

power socket.

4. Do not use this heater in the immediate

surroundings of a bath, a shower or a

swimming pool.

5. If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its service

agent or similarly qualified person in order to

avoid hazard. The heater contains no user

serviceable parts. Should the product suffer

damage or breakdown, it must be returned to

the manufacturer or their service agent.

6. Under the environment with electrical fast

transient, the product may malfunction and

require user to reset the product.

DESCRIPTIONS:

A. Heater Housing

B. Neck

C. Pedestal Pole with 2 Halves

D. Base

E. Locking Nut

F. Power Cord

G. Remote Control Sensor

H. Power Light

I. Mode Button

J. Oscillation Button

K. Set Temperature/Timer Buttons

+ for Up

- for Down

L. Timer Button

ASSEMBLY INSTRUCTIONS

(SEE FIG. 1 AND 2)

If you are planning on using the pedestal, start

with Step 1

Step 1 – Turn the heater housing (A) upside

down and place on a firm, level surface

Step 2 – Unscrew the locking nut (E) by turning

counterclockwise. Slide the locking nut (E)

and base (D) to the end of the power cord.

Step 3 – Unclip the two halves of the pedestal

pole (C) and re clip the two halves (C)

around the power cord (F), insert the 2

fixing screws. (see Fig. 1)

Step 4 – Screw the pedestal pole (C) clockwise

onto the neck (B) threaded end on the

bottom of the heater housing (A) until

you feel resistance. (see Fig. 2)

Step 5 – Slide the base (D) and the locking nut

(E) up the cord, smooth surface facing

up. Make sure to align the dot on the

back of the base to the dot on the

pedestal pole (C) before tightening the

locking nut (E) (See Fig. 2).

Step 6 – Hold base (D) straight while tightening

the locking nut (E) by turning clockwise.

Step 7 – Insert the power cord into the notch at

the rear of the base.

Step 8 – Carefully turn the heater upright, place

on a firm, level surface.

OPERATING INSTRUCTIONS

Frost Guard

This special setting is automatically activated

when the (AF) mode is selected. In this mode,

the heater is off until the room's temperature

reaches freezing and the heater automatically

turns on HI power. The heater will cycle ON and

OFF as it maintains the temperature between 5-

8 °C.

Setting the Fan

Press the Mode Button ( ) once to operate

the fan only (FA).

Setting the Digital Thermostat:

Your heater is equipped with a Digital

Thermostat that allows you to set your heater to

your precise comfort level.

1. Press the Mode Button ( ) twice for manual

HI power. The heater will run continuously on

HI.

2. Press the Mode Button again for manual LO

power. The heater will run continuously on LO.

3. Press the Mode Button for a fourth time for Auto

Mode HI Power (AH) or press again for Auto

Mode LO Power (AL). In either of these modes

you may then press the up (+), and down (-)

buttons to set your desired temperature.

4. Once you have set your desired temperature,

the display will return to current room

temperature and gradually increase until the

room has reached the preset temperature.

5. If the unit will not start in the digital thermostat

mode, please make sure the “set temperature” is

higher than the current room temperature.

NOTE: It is normal for the heater to cycle ON

and OFF as it maintains the preset

temperature. To prevent the unit from cycling,

you need to raise the thermostat setting.

When the preset temperature is reached, the

fan will run for 30 seconds without heat. This

cool down process ensures an accurate and

consistent temperature reading.

6. Press the Mode Button one more time to turn

the heater to (AF) mode and one final time to

turn the heater off. When the heater is off, the

room temperature will only be displayed.

NOTE: The Mode Button can be pressed and

held for 3 seconds at any time to turn the heater

off.

NOTE: AccuTemp Plus

TM

has memory. The digital

thermostat will remember the previous temperature

setting after the unit has been turned off. However,

if the unit is unplugged, the digital thermostat will

be reset and will no longer remember the previous

temperature setting. If you unplug the heater, you

will have to reset the AccuTemp Plus

TM

again by

following the above instructions.

USING THE PROGRAMMABLE TIMER

AccuTemp Plus

TM

allows the user to program the

heater to turn on at a preset time, or turn off

after a set amount of time.

NOTE: At any time, the timer can be turned off

by selecting 0 hours.

U.K. and IRELAND

2

3

Βαθμολογία

Περισσότερα για αυτό το εγχειρίδιο

Κατανοούμε ότι είναι ωραίο να έχετε ένα χάρτινο εγχειρίδιο για το Bionaire BFH3520 Θερμάστρα σας. Μπορείτε πάντα να κατεβάσετε το εγχειρίδιο από τον ιστότοπό μας και να το εκτυπώσετε μόνοι σας. Εάν θέλετε να έχετε ένα πρωτότυπο εγχειρίδιο, σας συνιστούμε να επικοινωνήσετε με το Bionaire. Μπορεί να είναι σε θέση να παρέχουν ένα πρωτότυπο εγχειρίδιο. Αναζητάτε το εγχειρίδιο του Bionaire BFH3520 Θερμάστρα σας σε διαφορετική γλώσσα; Επιλέξτε τη γλώσσα που προτιμάτε στην αρχική μας σελίδα και αναζητήστε τον αριθμό μοντέλου για να δείτε αν τον έχουμε διαθέσιμο.

Προδιαγραφές

Όλα τα εγχειρίδια για Bionaire Θερμάστρες
Περισσότερα εγχειρίδια του Θερμάστρες

Συχνές ερωτήσεις σχετικά με Bionaire BFH3520 Θερμάστρα

Η ομάδα υποστήριξής μας αναζητά χρήσιμες πληροφορίες προϊόντος και απαντήσεις σε συχνές ερωτήσεις. Εάν εντοπίσετε ανακρίβεια στις συνήθεις ερωτήσεις μας, ενημερώστε μας χρησιμοποιώντας τη φόρμα επικοινωνίας.

Σχετικά προϊόντα

Εγχειρίδιο

Bionaire BOH2503 Θερμάστρα

Εγχειρίδιο

Bionaire BOF1500 Θερμάστρα

Εγχειρίδιο

Bionaire BOH1503 Θερμάστρα

Εγχειρίδιο

Bionaire BCH160 Θερμάστρα

Εγχειρίδιο

Bionaire BOH2003B Θερμάστρα

Εγχειρίδιο

Bionaire BPH1414 Θερμάστρα

Εγχειρίδιο

Bionaire BOH2003 Θερμάστρα

Εγχειρίδιο

Bionaire BOH1501 Θερμάστρα

Σχετικές κατηγορίες