10
EN ORIGINAL INSTRUCTIONS
SPECIFIED CONDITIONS OF USE
The cordless angle grinder is intended for grinding, sanding, and
cutting metal, stone, and ceramic materials.
Use the cutting guard from the accessories range for cutting
application.
Refer to the instructions supplied by the accessory manufacturer.
The product is suitable only for working without water.
Do not use the product for any other purpose.
WARNING! Read all safety warnings, instructions,
Failure to follow all instructions listed below may result in electric
ANGLE GRINDER SAFETY WARNINGS
SAFETY WARNINGS COMMON FOR GRINDING, SANDING OR
CUTTING-OFF OPERATIONS:
Failure to follow all instructions listed below may result in electric
Operations for
which the power tool was not designed may create a hazard and
Such a conversion may result in a loss of control and cause serious
Just because the
accessory can be attached to your power tool, it does not assure
safe operation.
Accessories running
Incorrectly sized accessories cannot be adequately guarded or
controlled.
Accessories that do not match the mounting hardware of the power
tool will run out of balance, vibrate excessively and may cause loss
of control.
inspecting and installing an accessory, position yourself and
Damaged accessories will normally break apart during this test time.
The eye protection must be capable of
by the particular application. Prolonged exposure to high intensity
noise may cause hearing loss.
Fragments of workpiece or of a broken accessory may
Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and could give the operator an
electric shock.
The spinning accessory may grab the surface
and pull the power tool out of your control.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
The motor’s fan will
draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
Sparks could ignite these materials.
Using
water or other liquid coolants may result in electrocution or shock.
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be forced in the direction
opposite of the accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch
point can dig into the surface of the material causing the wheel to
from the operator, depending on direction of the wheel’s movement
at the point of pinching. Abrasive wheels may also break under
these conditions.
operating procedures or conditions and can be avoided by taking
proper precautions as given below:
•
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
•
Accessory may kickback over your hand.
•
Kickback will propel the tool in
the direction opposite to the wheel’s movement at the point of
snagging.
•
Corners,
sharp edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
•
Such blades create frequent kickback and
loss of control.
SAFETY WARNINGS SPECIFIC FOR GRINDING AND CUTTING-
OFF OPERATIONS
Wheels
for which the power tool was not designed cannot be adequately
guarded and are unsafe
An improperly
cannot be adequately protected.
The guard helps to protect
the operator from broken wheel fragments, accidental contact with
wheel and sparks that could ignite clothing.
Abrasive
cut-off wheels are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
Λάβετε μέρος στη συζήτηση σχετικά με αυτό το προϊόν
Εδώ μπορείτε να μοιραστείτε τη γνώμη σας για το AEG BEWS18125X20 Γωνιακός τροχός. Εάν έχετε κάποια ερώτηση, διαβάστε πρώτα προσεκτικά το εγχειρίδιο. Το να ζητήσετε ένα εγχειρίδιο μπορεί να γίνει χρησιμοποιώντας τη φόρμα επικοινωνίας μας.