Εγχειρίδιο Hikoki CR 13VEY Παλινδρομικό πριόνι

Εγχειρίδιο

3

English

5) Service

a) Have your power tool serviced by a qualifi ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and infi rm persons away.

When not in use, tools should be stored out of reach of

children and infi rm persons.

RECIPROCATING SAW SAFETY

WARNINGS

1. Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could

give the operator an electric shock.

2. Use clamps or another practical way to secure and

support the workpiece to a stable platform.

Holding the workpiece by hand or against your body

leaves it unstable and may lead to loss of control.

ADDITIONAL SAFETY WARNINGS

1. Preparing and checking the work environment. Make

sure that the work site meets all the conditions laid forth

in the precautions.

2. Ensure that the power source to be utilized conforms

to the power requirements specifi ed on the product

nameplate.

3. Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

4. When the work area is removed from the power source,

use an extension cord of suffi cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

5. Prior to cutting into walls, ceilings or fl oors, ensure there

are no electric cables or conduits inside.

6. Dust produced in operation

The dust produced in normal operation may aff ect the

operator’s health. To wear a dust mask is recommended.

7. When using this unit continuously, the unit may overheat,

leading to damage in the motor and switch. Therefore,

whenever the housing becomes hot, give the saw a

break for a while.

8. If the machine is used continuously at minimum speed,

an extra load is applied to the motor which can result in

motor seizure. Always operate the power tool so that

the blade is not caught by the material during operation.

Always adjust the blade speed to enable smooth cutting.

9. Always hold the body handle and front cover of the

power tool fi rmly. Otherwise the counterforce produced

may result in inaccurate and even dangerous operation.

10. Mounting the blade (Fig. 5)

This unit employs a detachable mechanism that enables

mounting and removal of saw blades without the use of a

wrench or other tools.

○ Turn off the switch and unplug the power cord.

Be absolutely sure to keep the switch turned off and the

power cord unplugged to prevent any accident.

○ Pull the back of the saw blade two or three times by hand

and check that the blade is securely mounted. When

pulling the blade, you will know it is properly mounted if it

clicks and the lever moves slightly.

○ When pulling the saw blade, be absolutely sure to pull it

from the back. Pulling other parts of the blade will result

in an injury.

11. Maintenance and inspection of saw blade mount

○ After use, blow away sawdust, earth, sand, moisture,

etc., with air or brush them away with a brush, etc., to

ensure that the blade mount can function smoothly.

○ As shown in Fig. 14, carry out lubrication around the

blade holder on a periodic basis by use of cutting fl uid,

etc.

○ Continued use of the tool without cleaning and lubricating

the area where the saw blade is installed can result in

some slack movement of the lever due to accumulated

sawdust and chips. Then, clean up the inside of the

blade holder with air and the like and carry out suffi cient

lubrication.

○ Do not use any saw blade with a worn-out blade hole

(A). Otherwise, the saw blade can come off , resulting in

personal injury. (Fig. 1)

12. Adjusting the swing cutting operation

○ Even for soft materials, you should perform straight

cutting if you wish to make curved or clean cuts.

○ Dust and dirt accumulated on the change lever

section can degrade the function of the change lever.

Periodically clean the change lever section.

○ When performing swing cutting, use a saw with straight

blade. If a saw with curved blade is used, the saw blade

may be broken or the unit may be damaged.

13. How to use

○ Avoid carrying it plugged to the outlet with your fi nger on

the switch. A sudden startup can result in an unexpected

injury.

○ Be careful not to let sawdust, earth, moisture, etc., enter

the inside of the machine through the plunger section

during operation. If sawdust and the like accumulate in

the plunger section, always clean it before use.

○ Do not remove the front cover. Hold fi rmly the front cover

by hand to operate. But, do not extend your hand or

fi nger beyond the fl ange of front cover to avoid an injury.

○

During use, press the base against the material while

cutting.

Vibration can damage the saw blade if the base is not

pressed fi rmly against the workpiece.

Furthermore, a tip of the saw blade can sometimes

contact the inner wall of the pipe, damaging the saw blade.

○ Select a saw blade of the most appropriate length.

Ideally, the length protruding from the base of the saw

blade after subtracting the stroke quantity should be

larger than the material (see Fig. 10).

If you cut a large pipe, large block of wood, etc., that

exceeds the cutting capacity of a blade; there is a risk

that the blade may contact with the inner wall of the pipe,

wood, etc., resulting in damage.

○ To maximize cutting effi ciency for the materials you are

using and working conditions, adjust the speed of the

saw blade and the switching to swing cutting.

Cutting

○ Press the base fi rmly against the workpiece.

○ Never apply any unreasonable force to the saw blade

when cutting. Doing so can easily break the blade.

○ Fasten a workpiece fi rmly before operation. (Fig. 11)

○ When cutting metallic materials, use proper machine

oil (turbine oil, etc.). When not using liquid machine oil,

apply grease over the workpiece.

The service life of the saw blade will be drastically

shortened if you don’t use machine oil.

○ Never apply any unreasonable force to the saw blade

when cutting. Also remember to press the base against

the lumber fi rmly.

Sawing curved lines

○ We recommend that you use the BI-METAL blade

mentioned in Table 2 for the saw blade since it is tough

and hardly breaks.

0000Book̲CR13VEY.indb30000Book̲CR13VEY.indb3 2018/12/2712:10:432018/12/2712:10:43

Βαθμολογία

Περισσότερα για αυτό το εγχειρίδιο

Κατανοούμε ότι είναι ωραίο να έχετε ένα χάρτινο εγχειρίδιο για το Hikoki CR 13VEY Παλινδρομικό πριόνι σας. Μπορείτε πάντα να κατεβάσετε το εγχειρίδιο από τον ιστότοπό μας και να το εκτυπώσετε μόνοι σας. Εάν θέλετε να έχετε ένα πρωτότυπο εγχειρίδιο, σας συνιστούμε να επικοινωνήσετε με το Hikoki. Μπορεί να είναι σε θέση να παρέχουν ένα πρωτότυπο εγχειρίδιο. Αναζητάτε το εγχειρίδιο του Hikoki CR 13VEY Παλινδρομικό πριόνι σας σε διαφορετική γλώσσα; Επιλέξτε τη γλώσσα που προτιμάτε στην αρχική μας σελίδα και αναζητήστε τον αριθμό μοντέλου για να δείτε αν τον έχουμε διαθέσιμο.

Προδιαγραφές

Όλα τα εγχειρίδια για Hikoki Παλινδρομικά πριόνια
Περισσότερα εγχειρίδια του Παλινδρομικά πριόνια

Συχνές ερωτήσεις σχετικά με Hikoki CR 13VEY Παλινδρομικό πριόνι

Η ομάδα υποστήριξής μας αναζητά χρήσιμες πληροφορίες προϊόντος και απαντήσεις σε συχνές ερωτήσεις. Εάν εντοπίσετε ανακρίβεια στις συνήθεις ερωτήσεις μας, ενημερώστε μας χρησιμοποιώντας τη φόρμα επικοινωνίας.

Σχετικά προϊόντα

Εγχειρίδιο

Hikoki CR 18DSL Παλινδρομικό πριόνι

Εγχειρίδιο

Hikoki CR 13VBY Παλινδρομικό πριόνι

Εγχειρίδιο

Skil 3470 DB Παλινδρομικό πριόνι

Εγχειρίδιο

Skil 3480 CA Παλινδρομικό πριόνι

Εγχειρίδιο

FERM RSM1016 Παλινδρομικό πριόνι

Εγχειρίδιο

Nakayama BS1080 Παλινδρομικό πριόνι

Εγχειρίδιο

Parkside IAN 71919 Παλινδρομικό πριόνι

Εγχειρίδιο

Parkside IAN 104447 Παλινδρομικό πριόνι

Σχετικές κατηγορίες