Εγχειρίδιο GBC HeatSeal H425 Ελασματοποιητής

Εγχειρίδιο

5

G

Operation, hot lamination

1

Connect the power cord plug to the appropriate power source.

2

Push the power button to “ON” position. The red power indicator will

illuminate (fig.1).

3

Using the lamination guide located on the machine (fig.1), select the

appropriate temperature setting for the pouch gauge thickness and

material you are laminating using the rotary knob control.

Temperature Setting Guidelines

When laminating thin paper with light ink coverage, set the temperature

dial to the low end of the film gauge range. Thick paper with heavy ink

coverage requires higher settings within the range. Temperature settings

will vary due to the finish, chemistry, and heat absorption properties

of the material being laminated. If the laminated pouch is cloudy after

the first pass through the machine, adjust the temperature to the next

higher position and run it through again. If waviness occurs, reduce the

temperature to the next lower position. Always allow sufficient time for

the laminator temperature to adjust to the changes made to the settings.

4

When the laminator has reached the correct lamination temperature

the green (ready) light will illuminate.

5

Centre the item to be laminated within the pouch left to right with

the top edge against the sealed edge of the pouch (fig.2).

6

Insert the pouch with the sealed edge first into the machine (fig.3).

7

The laminated item will automatically exit at the rear of the machine.

After the pouch has stopped moving, carefully remove from the

machine and place on a cool flat surface for approximately one

minute for cooling (fig.4).

8

If you are finished laminating push the power switch to turn the

machine off.

Operation, cold lamination

1

Connect the power cord plug to the appropriate power source.

2

Push the power button to “ON” position. The red power indicator will

illuminate (fig.1).

3

Rotate the temperature dial to position.

4

Follow the instructions included with your GBC self adhesive

laminate or other pressure sensitive, non thermal laminating

pouches.

Reverse feature

In the event of a misfeed or a jam follow these instructions.

1

Press the reverse button and hold down (fig.5). This will reverse

the rotation of the rollers allowing the pouch to exit the front of the

machine.

2

Pull the document out of the laminator.

3

After the document is out of the machine clean the rollers by

running the cleaning sheet through the laminator.

Caution: Use caution when removing the laminated pouch

from the machine. It may be hot.

m

Note

1

Never insert the loose end of the pouch first into the machine. This

could cause the machine to jam.

2

Never attempt to do single sided lamination. This will cause the

machine to jam.

3

After laminating run a clean card through the machine to clean glue

residue off of the rollers. This will extend the life of the rollers.

Guarantee

Operation of this machine is guaranteed for two years from date of

purchase, subject to normal use. Within the guarantee period, ACCO

Brands Europe will at its own discretion either repair or replace the

defective machine free of charge. Defects due to misuse or use for

inappropriate purposes are not covered under the guarantee. Proof

of date of purchase will be required. Repairs or alterations made by

persons not authorised by ACCO Brands Europe will invalidate the

guarantee. It is our aim to ensure that our products perform to the

specifications stated. This guarantee does not affect the legal rights

which consumers have under applicable national legislation governing

the sale of goods.

Register this product online at www.accoeurope.com

Βαθμολογία

Περισσότερα για αυτό το εγχειρίδιο

Κατανοούμε ότι είναι ωραίο να έχετε ένα χάρτινο εγχειρίδιο για το GBC HeatSeal H425 Ελασματοποιητής σας. Μπορείτε πάντα να κατεβάσετε το εγχειρίδιο από τον ιστότοπό μας και να το εκτυπώσετε μόνοι σας. Εάν θέλετε να έχετε ένα πρωτότυπο εγχειρίδιο, σας συνιστούμε να επικοινωνήσετε με το GBC. Μπορεί να είναι σε θέση να παρέχουν ένα πρωτότυπο εγχειρίδιο. Αναζητάτε το εγχειρίδιο του GBC HeatSeal H425 Ελασματοποιητής σας σε διαφορετική γλώσσα; Επιλέξτε τη γλώσσα που προτιμάτε στην αρχική μας σελίδα και αναζητήστε τον αριθμό μοντέλου για να δείτε αν τον έχουμε διαθέσιμο.

Προδιαγραφές

Όλα τα εγχειρίδια για GBC Ελασματοποιητές
Περισσότερα εγχειρίδια του Ελασματοποιητές

Σχετικά προϊόντα

Εγχειρίδιο

GBC Fusion 3100L Ελασματοποιητής

Εγχειρίδιο

GBC HeatSeal QuickStart H420 Ελασματοποιητής

Εγχειρίδιο

GBC Fusion 3000L Ελασματοποιητής

Εγχειρίδιο

GBC Proseries 3600 Ελασματοποιητής

Εγχειρίδιο

GBC HeatSeal H220 Ελασματοποιητής

Εγχειρίδιο

GBC Fusion 3200L Ελασματοποιητής

Εγχειρίδιο

GBC Inspire+ Ελασματοποιητής

Εγχειρίδιο

GBC HeatSeal H318 Ελασματοποιητής

Σχετικές κατηγορίες